WL-5460APv2 firmware E8

Notice:
-This firmware can only be used on WL-5460AP, please do not use it on WL-5450AP
or non OvisLink Corp. product.  Using it on non-ovislink AP or burning it by 
serial interface can cause permanent damage to your AP.  

-Using this firmware on other maker's product is a violation of OvisLink Corp's copyright.  
Violators will be prosecuted to the maximum penality imposed by law.

-After firmware update, if you have problem with the Web Configuration.  Please try to remove
the Google and Yahoo! tool bar.

-After firmware upgrade, the settings are restored to factory's default values.

-Please read the Quick Setup Guide(WL-5460APv2_QSG.PDF & WL-5460APv2_Manual.pdf) after Upgrade.  

-When in WISP mode, the DHCP server is turned on.  In all other modes, the DHCP server is turned off.

-Damage caused by the use of third party firmware that is not approved by OvisLink Corp. will void your warranty

-if the WL-5460AP users want to upgrade firmware from WL-5460AP-v2-eX(X stands for any number) firmware to third party.  
 The user need to downgrade their firmware to WL-5460AP-3.2.1.3.9eu firmware(available on our download page) first 
 before upgrading to third party firmware.  Otherwise, it might cause crash.
 

----------------------
Upgrade Procedure (upgrading from older non-WL-5460APv2 firmware):
1. Please update the firmware using "Intermediate-firmware.bin" file first.
   Please do not power off or touch the web page until the upgrade is completed.
2. After upgrade is completed.  Refresh your web browser.
3. Then update the firmware using "WL-5460AP-v2-e8-b1-firmware.bin" 

----------------------
Upgrade Procedure (upgrading from WL-5460APv2-e5 or WL-5460APv2-e6 or WL-5460APv2-e7):
1. Update the firmware using "WL-5460AP-v2-e8-b1-firmware.bin".
   Please do not power off or touch the web page until the upgrade is completed.


----------------------
Release Notes:
1. Adds ACK timeout adjustable.
2. Adds WISP(Client Router) mode
3. Adds Universal Repeater mode
4. Adds WISP + Universal Repeater mode
5. Adds DHCP Relay Function
6. Adds PPPoE WAN access
7. Adds manual entry for Clone MAC address
8. Show wireless MAC address on the status page
9. Add PPPoE MPPE Support
10. Fix WAN PING Issue
11. Fix Client table issue
12. Turn off the DHCP server by default
13. Turn on the DHCP server only if in WISP mode
14. When in WISP mode, the WAN PING and Remote Management is now turned on by default.
15. Fix DHCP server function in AP and Client Mode.
16. Fix watchdog problem in WISP mode
17. Improve System Stability
18. Add Wireless Client Isolation function
19. Re-measure TX Power Regulation

---------------------
Measured TX Power(dBm)

Note: These values are for your reference only.  OvisLink Corp does not guarantee
these values.  The result might vary +/- 2dB between different channels and machines

Setting         Highest    High        Middle      Low        Lowest  (dbm)
-----------------------------------------------------------------
[G mode]
Ave             14.14      13.06       11.15       7.76       1.38  
Peak            14.096     13.04       11.08       7.692      1.318
-----------------------------------------------------------------
[Mixed mode]
Ave             18.68      17.64       15.20      12.68      10.52  
Peak            18.664     17.642      15.18      12.67      10.512
-----------------------------------------------------------------
[B mode]
Ave             18.69      17.62       14.88      12.21      10.31  
Peak            18.674     17.578      14.854     12.172     10.304

